Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 33 Next »

Introduction

This section deals with the creation of a virtual dual carriageway that mimics the actual carriageway that will be beside where the radar or radars have been physically installed.

It is necessary to have a virtual carriageway in order to accurately detect, analyse and report incidents observed by the radar. The virtual carriageway creates parameters around the actual detection area.

The ClearWay™ program cannot function without at least one carriageway.

Contents

Drawing a Carriageway

  1. Enable the Configuration Mode, then select Carriageways from the Configuration Tree. Select New from the Configuration Panel; this will open a list of new feature options. Select Carriageway:

    image-20241113-080637.png

  2. The Create and Draw New Carriageway wizard window will appear. Drag this window to one side, and the plumb line for your carriageway should be visible in the middle of the PPI having a white horizontal line, with three nodal points and orange arrows indicating the direction:

    image-20241113-080854.png

  3. You can now use the nodes of the plumb line in order to plot your carriageway along the centre of the road:
    a. Hold down the Ctrl key to move the entire carriageway.
    b. Select individual circular nodes to place and change direction of carriageway sections.
    c. Right Click on the square graphic to create more circular nodes.
    d. Right Click on the circular nodes to delete them.
    e. Zoom in on your carriageway for greater detail with either your mouse, track pad or using the toggle direction and zoom keys in the top left hand corner of the Open Street Map display.

  4. The Open Street Map or Google Map gives a visual guide to the position of the carriageway, but if your radars are live, they should also be transmitting visual data. You can use a combination of the map and the visual data from the radar in order to accurately plot your carriageway.

  5. In the example below we have used the Open Street Map for clarity. The white end nodes have been moved to the start and end of the carriageway by selecting them with the mouse and moving them, and the centre node to middle of the carriageway. Note that the direction of the carriageway is heading south:

    image-20241113-081123.png

  6. In the example below more nodes have been added to follow the curve of the road:

    image-20241113-081348.png

  7. You can zoom into the carriageway to check that it has been drawn correctly. The nodes have been positioned in the centre of the dual carriageway where the carriageway separation is located:

    image-20241113-140709.png

  8. Complete the plotting of the carriageway:

    image-20241113-141130.png

You can edit the shape, direction and nodal points of the carriageway after plotting and completing the Create and Draw New Carriageway wizard. The plum line plan is not permanent. You can also move back and forth between the stages of the wizard if you wish to return to editing the carriageway in its plumb line state.

Carriageway Configuration

image-20241113-153236.png

Once your initial carriageway is plotted you can return to the Create and Draw New Carriageway window. You can now configure the carriageway and its Rules - these decide what objects and behaviours you wish the radar to detect.

  1. In the example below, the Create Dual Carriageway option has been selected with two lanes and the Lane Width and Carriageway Separation have been amended to suit the carriageway on the PPI. For more information about these and other settings please refer to: https://navtechradar.atlassian.net/wiki/spaces/TUN/pages/edit-v2/789512667#Carriageway-Wizard-Settings and https://navtechradar.atlassian.net/wiki/spaces/TUN/pages/edit-v2/789512667#Carriageway-Wizard-Settings.

    image-20241113-150204.png

  2. When you have selected the rules, click Next and you are given the opportunity to amend the key attributes of each selected rule. Each has a separate tab. Once satisfied with your Rules' configuration, click Finish:

    image-20241113-150308.png

  3. Your virtual carriageway should now appear on the main display with sections showing based on the selected section length.

    image-20241113-154145.png

  4. You can zoom into the carriageway to check that it has been drawn correctly:

    image-20241113-154230.png

Carriageway and Draw New Carriageway Wizard Settings

image-20241113-154602.png

Create Dual Carriageway: Select if your carriageway is a dual carriageway - traffic flowing in both directions.
Section Length (m): The length of the segments your carriageway will be divided into in order to divide the surveillance of the carriageway equally between the radar.

Number of Lanes: The number of lanes on each carriage way - each direction of traffic.
Use Single Lane Width: This option will set all lanes to the same Lane Width value. The Lane Width fields within the Lane Grid below will then be disabled. If you clear the check box, these fields become editable and you can then set each Lane Width independently.
Lane Width (m): The width of one lane in your carriageway.
Lane Grid:

Lane: This is the number of the lane.

Reversed Lanes: Select this option if you require a carriageway with bidirectional traffic, for example, Single Carriageways. This will then allow you to select which lane you wish to have with a reversed direction.

Lane Width: This determines the width of each lane. If you are using Use Single Lane Width then these fields will be disabled.

Carriageway Separation (m): The distance of the barrier between the carriageways. This is only applicable to a dual carriageway, and will be hidden if Create Dual Carriageway has not been selected.

Right Hand Drive: Select if your carriageway is in a country with right hand side drive.

Virtual Tracking Areas: Selected by default. This forces the software to generate appropriate tracking detection areas that match the carriageway. These areas are created dynamically when the software starts and when any changes are made to the layout of the carriageway.

Virtual Debris Tracking Areas: Selected by default. This forces the software to generate appropriate debris detection areas that match the carriageway. These areas are created dynamically when the software starts and when any changes are made to the layout of the carriageway.
Rules: all AID (Automatic Incident Detection) rules are selected by default, however you can deselect the rules you don’t need.

Carriageway Wizard Rule Settings

image-20241112-153944.png

Description: The object or action the rule applies to.

Alarm Description: A description of the alarm event, which will be displayed to the user.

Break Count: The number of times a rule has to be met before an alarm is raised.

Use Allowance Curve: The dynamic adjustment of the time it takes to generate an alarm based on how often the rule conditions are satisfied. This option is always recommended for ClearWay™.

Classification: What type of moving object.

Speed: Applies the rule only to tracks matching the specific speed value.

Is Smaller Than (<)

Is Smaller Than Or Equal To (≤)

Is Greater Than (>)

Is Greater Than Or Equal To (≥)

Is Equal To (=)

Is Different To (≠)

Is Between (><)

Is Outside (<>)

Video

The following video demonstrates the creation of a two lane dual carriageway:

Adding a Carriageway.mp4

Related Information

  • No labels

Safety is everything.