ICD-001 Status Report

Example Status Report

<?xml version="1.0" encoding="utf-8"?>
<StatusReport xmlns="ICDNAV001-StatusReport">
  <Sender SenderId="SenderId1" NetworkAddress="127.0.0.1" NetworkPort="6317" />
  <!-- Module Track Engine 1 is offline -->
  <ModuleStatus Name="TE1" Reported="2019-04-03T22:05:02.112" Status="Offline" ModuleId="710e8979-effb-4d2d-94d4-205aa4bd0eae" />
  <ModuleStatus Name="TE2" Reported="2019-04-03T22:05:02.112" Status="Online" ModuleId="C565AE57-95C5-4C17-8CF3-E19609067500" />
  <ModuleStatus Name="Camera Controller" Reported="2019-04-03T22:05:02.112" Status="Online" ModuleId="AF648F4D-3342-406E-888A-F4FAD05B36AA"/>
  <!-- Radar 1 being reported as offline - therefore no health metric can be reported -->
  <RadarHealth RadarId="1" Name="Radar 1" Reported="2019-04-03T22:05:02.112" Packets="0" Temp="0" Rotation="0" Status="Offline" />
  <!-- Radar 2 being reported as online but with a warning status because the temperature is too high -->
  <RadarHealth RadarId="2" Name="Radar 2" Reported="2019-04-03T22:05:02.112" Packets="801" Temp="89" Rotation="2.0" Status="Warning" />
  <RadarHealth RadarId="3" Name="Radar 3" Reported="2019-04-03T22:05:02.112" Packets="800" Temp="59" Rotation="2.01" Status="Online" />
  <!-- The current system profile is the set to the default -->
  <SystemProfileStatus Name="Default" ProfileId="-1" Reported="2019-04-03T22:05:02.112" />
  <AreaSummary Reported="2019-04-03T22:05:02.112">
    <AreaStatus Type="General" Name="Front Gate" AreaId="1" Enabled="Enabled" />
    <AreaStatus Type="Detection" Name="Detection North" AreaId="2" Enabled="Enabled" />
    <AreaStatus Type="Alarm" Name="Alarm Zone A" AreaId="3" Enabled="Disabled" />
  </AreaSummary>
</StatusReport>

Module Status Element

The module status is essentially a heartbeat. Each module typically sends a heartbeat message every 5 seconds. For each module, assuming a heartbeat has been received, a status element will be added to the status report. If a status element is not present, then either the heartbeat has been delayed or the module has gone offline.

Module Status Attributes

Optional attributes are formatted in italics and highlighted with an asterisk.

Attribute	Description	Type	Unit
Name	Name of the module.	String
Reported	Time status was reported.	DateTime
Status	Status of module connection – options are:· Online Warning Offline	ModuleStatusList
ModuleId*	Unique identifier for the module (optional).	String (representation of a GUID / UUID)
ModuleType*	Module type (optional). This is available in Witness 4.0 and higher.	String
HostIP*	IP of the server hosting the module (optional). This is available in Witness 4.0 and higher.	String

Radar Health Element

The radar health element provides specific health details for each sensor in the system. If a radar is active and connected then the Witness system will receive regular health updates. The latest health report for each radar is added to the status report. If a recent health update has not been received for any of the radar then there will be no element for that radar.

Radar Health Attributes

Attribute	Description	Type	Unit
RadarId	ID of the radar	Long
Name*	User-friendly name of the radar (optional)	String
Reported	Time health was reported	DateTime
Packets	Radar packet rate per second. Value will vary depending on the range and mode of the radar	Double
Temp	The current operating temperature of the sensor	Double
Rotation	The current rotation rate of the radar. Some models of radar have different rotation speeds but the default is 1Hz.	Double
Status	Status of radar connection – options are: Online Warning Offline	ModuleStatusList

If the module or radar has been reported as being online, then if the system loses the connection to that application or device the status will change to reflect that. Typically, the application or device will change status from Online -> Warning -> Offline.

If a module or radar is removed from the list, then this would indicate the device has been shut down intentionally (i.e. a user stops a Bloodhound service) and should not be a cause for concern. In this situation the health will stop being reported for the removed device.

There is no status to indicate that any of the values contained within the health data are outside expected parameters. This checking should be performed by the 3^rd party based on suitable criteria for their own application.

Be aware that radar health can only be reported if the tracker is active. If a tracker goes offline, then no radar health will be reported for that tracker.

Trackers and their attached radar will always share the same Id (i.e. tracker ID:1 will be connected to radar ID:1).

In situations where Witness is being used with recorded or simulated data then do not expect to receive radar health updates.

System Profile Status Element

The system status element shows which system profile is currently active. The Id is the UserId of the profile and the name is also included to make the data more readable.

System Profile Status Attributes

Attribute	Description	Type	Unit
Name	User-friendly name of the current system profile	String
ProfileId	The profile Id of the current system profile	Integer
Reported	Time and date that the status was last reported	DateTime

Area Summary Element

The area summary element contains a list of Area Status elements. Each status element contains details on the area, including the user Id, name current state.

Attribute	Description	Type	Unit
Reported	Time and date that the status was last reported	DateTime

Area Status Element

Attribute	Description	Type	Unit
Type	The type of area. These map to the area types in Witness: General Detection Exclusion Camera Alarm Static Target Detection	AreaTypeList
Name	The user friendly name of the area	String
AreaId	The User Id for the area	Integer
Enabled	The current state of the area. Depending on the type of area, the state has different implications. For example, disabling an Alarm area means it cannot be used inside rules. If a Detection areas is disabled it means the tracker will not generate tracks in that area. Disabling an exclusion area will stop it excluding data from the tracker allowing it to generate tracks	Boolean

Related information

Page:

ICD-001 Track Filter Command (Witness 4.0)
Page:

ICD-001 Acknowledge Alarm Command (Witness 4.0)
Page:

ICD-001 Request Status Command (Witness 4.0)
Page:

ICD-001 Detection Command (Witness 4.0)
Page:

ICD-001 Update Entity Command (Witness 4.0)
Page:

ICD-001 System Profile Command (Witness 4.0)
Page:

ICD-001 External Trigger Command (Witness 4.0)
Page:

ICD-001 Plugin (Witness 4.0)
Page:

System Profiles (Witness 4.0)
Page:

ICD-001 Command Reply (Witness 4.0)
Page:

ICD-001 Camera Command (Witness 4.0)
Page:

ICD-001 Track Command (Witness 4.0)
Page:

ICD-001 Tracker Command (Witness 4.0)
Page:

ICD-001 Commands (Witness 4.0)
Page:

ICD-001 Change Log (Witness 4.0)