...
Introduction
This page covers accessing and navigating the SafeGuard™ Configuration Application Dashboard, which alerts a user to alarms caused by data exceeding threshold values quickly and easily.
It also provides a live view of a connected SafeGuard™ system, which includes some raw FFT data, NavMode radar data and SafeGuard™ configuration.
...
To monitor the system using FFT and NavMode level data, and make adjustments using the config.
...
Quickly and easily be alerted to data exceeding threshold values in either mode.
...
An option to visually link an output alarm state change with a radar return within or without one of the defined areas.
...
Ability to quickly identify areas that require immediate attention.
...
Provide an option to "look" at the raw radar data and see its proximity to the threshold value at each location.
...
.
...
...
The live display can be paused and can be reset to the most current view
...
Ability to review data when required.
...
Update rate of “live” data on visualiser matches that of the sensor update rate
...
Provides the ability to view real-time or close to real-time data.
...
The application can display raw radar data, with a minimum refresh rate of 1 Hz
...
Allow the viewing of up-to-date raw data
...
Application is able to display radar health, this can be abstracted to a single metric
...
Provides the ability to quickly assess the health of the system and identify any issues.
For more information about SafeGuard™ please refer to this documentation: SafeGuard™ User Guide.
Plan - this will be removed once this page has been completed.
...
Contents
...
| Table of Contents | ||||||
|---|---|---|---|---|---|---|
|
...
Navigating the Configuration Application Dashboard
...
...
PPI Navigation Control: Please refer to this page for more information: https://navtechradar.atlassian.net/wiki/spaces/TUNIA/pages/7736852832543026333/NavigatingPPI+AdvanceGuard#MainDisplay#PPI-Display-Features
...
The left hand side features a PPI, and the right hand side features three tabs: Settings, Navigation Data and AlarmsNavigation-Control.
PPI: Please refer to this page for more information: Configuration Application PPI Display.
SettingsRadar info Panel: Please refer to this page for more information: Configuration Application Settings https://navtechradar.atlassian.net/wiki/spaces/IA/pages/2543026333/PPI+Display#Radar-Info-Panel.
Navigation Data Tab: Please refer to this page for more information: Configuration Application Navigation Radar Point Data.
AlarmsSettings Tab: Please refer to this page for more information: Configuration Application Alarms
Risks
...
It might not be possible to update a raw data display in real time using standard UI technology - It's possible to update the raw data display in something close to real time, but only if we scale the image size down to 65% of the original size or less. With no scaling, 1Hz is possible
...
It might not be possible to display very large number of nav plots in real time using standard UI technology - it's possible to display either 1000 or 2000 at a time, based on a worst-case scenario where every azimuth had 5 peaks
...
Area Alarms Panel: Please refer to this page for more information: https://navtechradar.atlassian.net/wiki/spaces/IA/pages/2543026333/PPI+Display#Area-Alarms-Panel.
Data Controls: Please refer to this page for more information: https://navtechradar.atlassian.net/wiki/spaces/IA/pages/2543026333/PPI+Display#Data-Controls.
Mouse Coordinates: Please refer to this page for more information: https://navtechradar.atlassian.net/wiki/spaces/IA/pages/2543026333/PPI+Display#Mouse-Coordinates.
Log Panel: Please refer to this section for more information: https://navtechradar.atlassian.net/wiki/spaces/IA/pages/2543026333/PPI+Display#Log-Panel.
...
Related Information
| Filter by label (Content by label) | ||||||
|---|---|---|---|---|---|---|
|