Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

The debris detection system utilises a dedicated processing channel within the Navtech tracker. This channel is highly optimised to look for small, stationary objects which have appeared within the detection range of the radar. The system comes with a well-defined setup of default parameters which are designed to work with the CTS radar.

The Debris Detection Processing

The debris processing is quite different from the normal tracking approach. It is optimised for stationary targets. The key processes to support this are:

Panel
borderColorsilver

Table of Contents
maxLevel4

Long Term Clutter Map

In normal tracking the clutter map (long term average) has to update reasonably fast. This is to ensure normal clutter, such as trees and long grass, does not generate any false alarms. This works well with moving targets, such as normal traffic, however the downside is that tracks will be absorbed into the clutter map when they become stationary. This can happen in a matter of seconds which means stationary objects, such as debris, can be missed.

By having a much slower updating clutter map, stationary targets are observed for longer and the chances of seeing small, static objects are much improved. This approach does increase the probability of false alarms however we use the second key process, multi-scan analysis, to focus on just the targets we want to detect.

Multi-Scan Analysis

This process differs from the typical radar processing because it looks at data over several scans. Essentially it looks for signals which are greater than the specified signal threshold over a number of rotations. Depending on how many times it see a target exceed the threshold, the process will generate an artificial signal based on the total number of detections. This provides a high level of confidence that the object being examined is in fact a genuine piece of debris. The process does delay the creation of the track but typically this only by a few seconds.

Classification

The debris channel is configured to always report any target as debris. This sounds logical, but also consider that any stationary object, from small to large, could be reported as debris. This would include stopped vehicles or people standing still. This is a minor disadvantage consider the overall improvement in performance and futures versions of this feature will include more intelligent classification to correctly distinguish between small and large objects.

How to Configure Debris Detection

To enable the debris detection:

  1. Navigate to the Debris settings:
    1. Radar -> Tracker Settings -> Debris tab.
    2. Select Use Debris Channel.



  2. Once enabled, the next step is to draw the debris detection area. This area can be specific to this radar or a larger area that can be used by several radars.

    Info

    The debris area is completely independent of the normal tracking area (i.e. the carriageways). This enables you to define the debris detection system to operate in specific areas . In addition this also allows you to exclude areas of detection which may cause the debris detection specific problems and can be safely excluded without compromising the overall performance of the system. Like with normal tracking areas, you can create one or more for debris, per radar.

  3. Once the debris detection area has been created, you can add the area and tracking parameters to the tracker configuration:
    1. Enter Edit mode.
    2. Select the "+" key beside the Tracking Areas list.
    3. Select your debris area and the Debris Default tracking parameters.
    4. Select Save when complete.



  4. The default configuration is now complete.
Info
titleDebris Default Tracking Settings

The version of Witness that supports the new debris detection system now ships with default tracking parameters for this process. These are entitled Debris Default. This should always be used by default but can be customised for site-specific variations if required.

Default Configuration Overview

The default configuration has been designed around detecting debris with a radar cross section of 15cm2 out to 150m. This should work for most environments. However if you are encountering problems with false alarms, then you can consider altering the following settings:

Threshold Delta (Tracker->Debris->Threshold)

Default value: 16

This threshold works in exactly the same way as for normal processing, but it only applies to the debris channel. The threshold output is always levels above, therefore there are the normal area dependent threshold settings in the Debris Default tracking parameters, however we would encourage you to only use this global threshold setting. If you increase this value, you will desensitise the detection, decreasing the value will increase sensitivity and therefore increase the likelihood of nuisance alarms.

Full Window Size (Tracker->Debris->Scan to Scan Integration)